Search found 8 matches

by mikechris
Sun Jun 04, 2017 2:41 am
Forum: Projects
Topic: DataLogger-IO-8.37-Spreadsheet
Replies: 0
Views: 516

DataLogger-IO-8.37-Spreadsheet

Attached is an Excel-97 spreadsheet (and a PDF version) that defines the pins on most of the connectors on the DataLogger, a good place to start for any DataLogger project, includes both old and new connector numbers. Spreadsheet shows which IO require Firmware 8.37 to work correctly. See also "...
by mikechris
Sun May 28, 2017 6:05 am
Forum: Software issues
Topic: Datalogger IO Issue
Replies: 14
Views: 2250

Re: Datalogger IO Issue

My initial testing also looks good, thanks for the help.
by mikechris
Thu May 25, 2017 10:49 pm
Forum: Projects
Topic: SuperPro-IO Spreadsheet & Connector Layout
Replies: 0
Views: 460

SuperPro-IO Spreadsheet & Connector Layout

Attached is an Excel-97 spreadsheet that defines the pins on most of the connectors on the SuperPro, a good place to start for any SuperPro project. A PDF version is also provided. Attached is an easy to read .GIF file of a SuperPro5 connector layout diagram (based on not so easy to read DXF file on...
by mikechris
Tue May 23, 2017 2:49 am
Forum: Projects
Topic: SuperPro IO Test Program
Replies: 0
Views: 469

SuperPro IO Test Program

SuperPro IO Test Program The attached program will quickly test all the digital IO lines by driving the 8 outputs on a selected connector with 8 different test signals. The IO is grouped into 6 connectors with 8 IO on J10, J12, J13, J14, and J15; and 6 IO on J9. The program generates 1 pulse per mse...
by mikechris
Fri May 19, 2017 12:27 am
Forum: Software issues
Topic: Datalogger IO Issue
Replies: 14
Views: 2250

Re: Datalogger IO Issue

Serial Saga, Still have no luck getting TXD2 and TXD3 to work. Looking at the registers before starting the program and again at the "END" (before Reset, or Stop), can see the Function change for TXD1 from 0x.D0 (GPIO) to 0x.41 (Serial), and then back to 0x.D0 (GPIO) after Reset, as expect...
by mikechris
Thu May 18, 2017 2:50 am
Forum: Software issues
Topic: Datalogger IO Issue
Replies: 14
Views: 2250

Re: Datalogger IO Issue

Good news, the DOA board lives. You were right, it just needed some firmware, thanks. Using what you provided, I dug into the NPX manual and the LPC43xx.bas file to fix 8 more IO. The register programming is shown below: * &H40086184 = &HD4 ' IOCON pin mux for P3_1 * &H40086188 = &HD...
by mikechris
Tue May 16, 2017 6:41 am
Forum: Software issues
Topic: Datalogger IO Issue
Replies: 14
Views: 2250

Re: Datalogger IO Issue

Your quick fix for P2_2,3,4,5,6,8 works good, thanks. I can work around the other 9 outputs that remain dead, with the exception of the 2 UARTs that don't work. TXD1 works good, but TXD2 and TXD3 do not. Is there a quick fix for those two UART pins, or at least one? The "Include" does need...
by mikechris
Mon May 15, 2017 4:31 am
Forum: Software issues
Topic: Datalogger IO Issue
Replies: 14
Views: 2250

Datalogger IO Issue

I have an issue with many of the outputs on a new DataLogger not working. Not sure if I have a bad board (2nd board was DOA) or if it's a bug. I have successfully used many Coridium products over the years, only had one bad chip and found one bug (fixed in a day). Is it a bad board, a bug, or am I h...

Go to advanced search